ServicePedestal Settings

Set parameters for ServicePedestal. Parameters must be set before the system can be put into service.  

Basic settings

Basic settings for the equipment.

Factory reset

Load factory settings. All parameters are set to the specified factory settings.

• Must be performed before the equipment can be put into service

• Note that the equipment restarts

• Can be performed again if the factory settings need to be restored
• If licenses are changed, the factory reset must be performed again

The following global parameterA global parameter is shared and can be used by more than one system.  is adjusted automatically:   

• DWTYPE is set to an on/off output that is remembered across restart

Parameter	Index	Range	Format	Factory setting	Example
SEPFAC	-	-	-	-	SEPFAC

ProgramProgram type installed in the device.

Set which program the equipment must use.

• Must be selected before the equipment can be used

Parameter	Index	Range	Format	Factory setting	Example
SEPPRG	-	0..71	0 = Disabled 1 = MarinePro 2 = MarinePro V1 with water outletOutlet where water can be drawn from the equipment. (generation 1) 3 = MarinePro V2 with water outletOutlet where water can be drawn from the equipment. (generation 2) 4 = MarinePro V3 with water outletOutlet where water can be drawn from the equipment. (generation 3) 10 = MarinellaProPower Marinella is a service pedestal with electricity and water outlets for marinas. 11 = MarinellaProPower Marinella is a service pedestal with electricity and water outlets for marinas. with water outletOutlet where water can be drawn from the equipment. 12 = MarinellaProPower Marinella is a service pedestal with electricity and water outlets for marinas. NEO(V1) 13 = MarinellaProPower Marinella is a service pedestal with electricity and water outlets for marinas. NEO with water outletOutlet where water can be drawn from the equipment. (V1)   20 = Marineium  21 = Marineium with water outletOutlet where water can be drawn from the equipment.   30 = MarineMax  40 = ShoreSupply (without consumption settlement) 41 = ShoreSupply 50 = TallyKey 51 = TallyKey with water outlet 60 = Beas 61 = Beas with water outlet 70 = DockPoint 71 = DockPoint with water outlet     0 = Disabled 1 = MarinePro 2 = MarinePro G2  10 = MarinellaProPower Marinella is a service pedestal with electricity and water outlets for marinas. 20 = Marineium  30 = MarineMax  40 = ShoreSupply (without consumption settlement) 41 = ShoreSupply 50 = TallyKey 60 = Beas 70 = DockPoint	0	SEPPRG 1

Access control

Set how the customer is validated, or whether the equipment is available for free use.

• Must be selected before the equipment can be used

Parameter	Index	Range	Format	Factory setting	Example
SEPACC	-	0..3	0 = Blocked (the equipment is blocked and cannot be used) 1 = Free (the equipment is open to everyone for free use, and all consumption is registered to the system accountThe 'Unknown' system account in the customer database is used for consumption from unknown customers or equipment configured for free use.) 2 = Payment (the equipment validates the customer and only approved customers are accepted) 3 = Mixed (the equipment uses Payment first; if the customer is not approved, Free is used)	2	SEPACC 1

Name

Set the equipment name. The name is used, for example, if the equipment sends a messageA message sent by the equipment to one or more configured users, for example an SMS or email alarm..

• If no name is specified, the system nameName combined with messages sent by the equipment, such as the default system name 'Viking' or a user-selected name. is used
• Hint - the shorter the name, the more space there is for other text, for example when the name is combined with an alarm textExample alarm text: 'Viking - power supply is disconnected! Regards, Vikingegaarden'.

Parameter	Index	Range	Format	Factory setting	Example
SEPNAME	-	Max. 20 characters	Numbers or letters	-	SEPNAME Viking

Greeting

Set a greeting for the equipment. The greeting is used, for example, if the equipment sends a messageA message sent by the equipment to one or more configured users, for example an SMS or email alarm..

• If no greeting is specified, the system greetingGreeting text that can be combined with a message sent by the equipment, for example 'Regards, Vikingegaarden'. is used
• Hint - the shorter the greeting, the more space there is for other text, for example when the greeting is combined with an alarm textExample alarm text: 'Viking - power supply is disconnected! Regards, Vikingegaarden'.

Parameter	Index	Range	Format	Factory setting	Example
SEPREGARDS	-	Max. 20 characters	Numbers or letters	-	SEPREGARDS Vikingegaarden

Modules

Configure equipment modules. Note that modules are options and that the equipment can be supplied with or without modules.

Transient protection

Set whether the equipment has built-in transient protection.

Parameter	Index	Range	Format	Factory setting	Example
SEPTPO	-	0..2	0 = None 1 = Built in as NONormally open. 2 = Built in as NCNormally closed.	0	SEPTPO 1

Phase monitoring

Set whether the equipment has phase monitoring.

Parameter	Index	Range	Format	Factory setting	Example
SEPFKO	-	0..1	0 = None 1 = Built-in phase monitoring meter 2 = Monitoring via 3-phase energy meter 3 = Combined 1+2	0	SEPFKO 1

Energy meter

Set whether the equipment has a built-in energy meter for registering internal power consumption.

Parameter	Index	Range	Format	Factory setting	Example
SEPEGI	-	0..1	0 = None 1 = Built in	0	SEPEGI 1

Heating control

Set whether the equipment must control and monitor heating to protect water pipes against frost.

Parameter	Index	Range	Format	Factory setting	Example
SEPHEAT	-	0..1	0 = None 1 = Heating control	0	SEPHEAT 1

EnergyLogger

Set whether the equipment has built-in EnergyLogger for registering power consumption.

Parameter	Index	Range	Format	Factory setting	Example
SEPEEL	-	0..1	0 = None 1 = Built in	0	SEPEEL 1

Key reader

Set whether the equipment has a built-in aKeyaKey is a key fob reader for RFID cards, tags, and similar access media. key reader for registering, for example, RFIDRFID access cards, credit cards, or key tags can be used with a key reader for access control. cards.

Parameter	Index	Range	Format	Factory setting	Example
SEPAKR	-	0..1	0 = None 1 = Built in	0	SEPAKR 1

Power outlets

Set parameters for power outlets.

Count

Set how many power outlets the equipment is built with. For example, the equipment may be built with 4 power outlets.

• Must be selected before the equipment can be used

Parameter	Index	Range	Format	Factory setting	Example
SEPEAMOUNT	-	0..12	0 = No outlets 1 = 1 outlet 2 = 2 outlets 3 = 3 outlets ...	0	SEPEAMOUNT 4

Activation timeout

Set the time from when the plug is inserted until the power outlet must be switched on. If the time expires, the power outlet is paused. Another user can use the power outlet after the current plug is removed.

• For broad local access, a paused outlet normally requires the plug to be removed and inserted again. If there is a local switch, switch it off and on again.
• If the same outlet is deliberately selected in Emiko/App/Web, the equipment can try to start it again while the plug is still inserted, provided normal electrical safety checks pass. No plug means no power.

Parameter	Index	Range	Format	Factory setting	Example
SEPEONTIM	-	1..20	Number of minutes	8	SEPEONTIM 10

Auto stop

Set the time from the last registered energy consumption until the power outlet is automatically switched off. For example, if a power outlet is switched on and no energy consumption is registered during the specified period, the power outlet is automatically switched off.

Parameter	Index	Range	Format	Factory setting	Example
SEPEUSAGETIM	-	0..32000	0 = Function disabled >0 = Number of minutes	1440 (one day)	SEPEUSAGETIM 2880

Water outlets

Set parameters for water outletOutlet where water can be drawn from the equipment..

Count

Set the number of water outletOutlet where water can be drawn from the equipment. the equipment is built with. For example, the equipment may be built with 1 water outletOutlet where water can be drawn from the equipment..

• Must be selected before the equipment can be used

Parameter	Index	Range	Format	Factory setting	Example
SEPWAMOUNT	-	0..1	0 = No outlets 1 = 1 outlet	0	SEPWAMOUNT 1

Activation timeout

Set the time from when operation is switched on until the water outlet must open. If the time expires, the user normally starts again, or another user can use the water outlet.

• Broad local access such as aKey/RFID or phone/voice selection does not automatically start a paused water outlet.
• If the same water outlet is deliberately selected in Emiko/App/Web, the equipment can try to open it again when normal authorization and product checks pass.

Parameter	Index	Range	Format	Factory setting	Example
SEPWONTIM	-	1..20	Number of minutes	8	SEPWONTIM 10

Auto stop

Set the time from the last registered water consumption until the water outlet is automatically closed. For example, if a water outletOutlet where water can be drawn from the equipment. is opened and no water consumption is registered during the specified period, the water outlet is automatically closed.

Parameter	Index	Range	Format	Factory setting	Example
SEPWUSAGETIM	-	0..32000	0 = Function disabled >0 = Number of minutes	1440 (one day)	SEPWUSAGETIM 2880

Valve

Set parameters for the valve.

Valve type

Set which valve type is installed.

• Must be selected before the equipment can be used

Parameter	Index	Range	Format	Factory setting	Example
SEPVALTYPE#	1..3	0..3	0 = None 1 = Solenoid valve (On/Off) 2 = Solenoid valve (Pulse) 3 = Motor valve BFA 820	0	SEPVALTYPE 1

Water meter

Set parameters for the water meter.

Meter ratio

Set the water meter ratio. For example, 1 pulse corresponds to 10 liters of water.

• Note must only be set when a water meter with pulse output is used

Parameter	Index	Range	Format	Factory setting	Example
SEPSCALE#	1..3	0..1000	Number of liters of water per pulse	0	SEPSCALE1 10

Order number

Set parameters for use of order numberOrder number from an ERP system or similar source, used as a reference to the customer order.. When this function is used, the user can enter an order numberOrder number from an ERP system or similar source, used as a reference to the customer order., which is registered together with the power consumption. For example, when the user calls the equipment, an SMSSMS is a text message that can be sent or received with a mobile phone. is sent to the user, who must reply with the required order numberOrder number from an ERP system or similar source, used as a reference to the customer order.. When the equipment receives an SMSSMS is a text message that can be sent or received with a mobile phone. with an order numberOrder number from an ERP system or similar source, used as a reference to the customer order., the power outlet is switched on.

• Requires the user in Emiko to be marked as required to use order numberOrder number from an ERP system or similar source, used as a reference to the customer order.. If this function is required, contact the system administrator
• The order number can consist of numbers and letters and has a maximum length of 32 characters
• The order number can be blank
• Note - a license is required before this function can be used

Response time

Set the time from when the user receives the SMSSMS is a text message that can be sent or received with a mobile phone. until the user must reply with the order numberOrder number from an ERP system or similar source, used as a reference to the customer order.. If the user does not reply before the time expires, the user must, for example, call again and a new SMSSMS is a text message that can be sent or received with a mobile phone. is sent.

Parameter	Index	Range	Format	Factory setting	Example
SEPORDTIM	-	1..8	Minutes	2	SEPORDTIM 3

Lighting

Set parameters for how the lighting must function.

• Option - note that lighting is an option and the equipment can be supplied with or without lighting

Operating mode

Set operating mode. Lighting can be controlled manually or set to automatic. In automatic operation, the light turns on shortly before sunset and turns off shortly after sunrise.  

Parameter	Index	Range	Format	Factory setting	Example
SEPLIGHT	-	0..2	0 = Always off 1 = Always on 2 = Automatic (recommended)	2	SEPLIGHT 1

Output

Select output.

Parameter	Index	Range	Format	Factory setting	Example
SEPLIGOUT	-	0..7	0 = None 1 = Automatic (recommended) 2 = Output 1 3 = Output 2 4 = Output 8 5 = Output 16 6 = Output 28 7 = Output 40	1	SEPLIGOUT 1

 

 

Status

Status fields for reading values from the equipment.

License

Show the status of the equipment license.

• Note - status can only be read.

Status	Index	Range	Format	Factory setting	Example
LICSEP	-	-	Bit 1: 1 = Power outlets 1..2 enabled Bit 2: 1 = Power outlets 3..4 enabled Bit 3: 1 = Power outlets 5..8 enabled Bit 4: 1 = Power outlets 9..12 enabled Bit 10: 1 = Water outlet enabled Bit 11: 1 = OrdreManagerModule for registering an order number for a service purchase, such as electricity or water. enabled	-	Read-only