Use this page as a commissioning starting point for supported instruments where the factory or standard communication defaults are known.
Installed equipment can be changed in the field. Always verify the actual address and serial settings before replacing, scanning, or troubleshooting an instrument.
This optional reference contains only model-specific defaults. Select the generic communication template on Network Profile.
| Instrument | Setup | Default address | Connection | Baud rate | Serial format | Usable network profiles | Source | Notes |
Thies Hygro-Thermo-Baro Transmitter Compact 1.1006.54.081 |
107109100 Auto |
Modbus address 1; range 1..247 |
RS485 Modbus RTU | 9600 | 8N1 | 1 or 2 |
Manufacturer manual and controller support | Use Auto for normal setup. The controller identifies this supported variant during driver initialization. |
| Thies Clima sensors, general Modbus/RS485 family | 107109100 Auto where the controller can identify the sensor |
Sensor-dependent; manufacturer manuals may call this ID, Bus-ID, bus address, or slave address. | RS485 Modbus RTU when configured | Sensor-dependent | Sensor-dependent | Match the configured sensor. | Manufacturer manual, partial, and controller support | Do not copy the Hygro-Thermo-Baro default unless the installed sensor is that Modbus variant. Auto can identify the supported variants listed under Thies Clima Auto in Device Model. |
| Siemens SITRANS LR110 Modbus | 107116100 Auto or 107116101 specific |
Modbus address 246; range 1..255 |
RS485 Modbus RTU | 9600 | 8N1 | 1 or 2 |
Manufacturer manual and controller support | The manufacturer manual defines the default address, baud rate, parity, and stop bits. |
| Siemens SITRANS LR120 Modbus | 107116100 Auto or 107116102 specific |
Modbus address 246; range 1..255 |
RS485 Modbus RTU | 9600 | 8N1 | 1 or 2 |
Manufacturer manual and controller support | Same Siemens LR1x0 Modbus communication defaults as LR110. |
| OTT CBS Bubble Sensor | 107111100 Auto or 107111101 specific |
Modbus bus address 1; range 1..247 |
RS485 Modbus RTU | 9600 | No parity confirmed; stop bits not confirmed | Not ready for recommendation. | Manufacturer manual, partial, and controller support | Modbus is deactivated by factory default. Confirm the activated Modbus serial format before choosing a network profile. |
| Gill MaxiMet GMX600 | 107110100 Auto or 107110101 specific |
Not confirmed from manufacturer Modbus defaults. Modbus supports networked RS485 use. | RS485 Modbus RTU when configured | 19200 default; 9600 or 19200 for Modbus | Not confirmed | Not ready for recommendation. | Manufacturer manual, partial, and controller support | Exact Modbus address and serial format still need confirmation. Configure the instrument for Modbus before commissioning. |
| Carlo Gavazzi EM530 | See Device Model Setup | Modbus address 1; range 1..247 |
RS485 Modbus RTU | 9600 | 8N1 | 1 or 2 |
Manufacturer manual and controller support | Use the profile for the installed RS485 port. |
| Carlo Gavazzi EM540 | See Device Model Setup | Modbus address 1; range 1..247 |
RS485 Modbus RTU | 9600 | 8N1 | 1 or 2 |
Manufacturer manual and controller support | Use the profile for the installed RS485 port. |
| Janitza Auto | 101112100 |
Not confirmed from manufacturer defaults. | RS485 Modbus RTU | Not confirmed from manufacturer defaults. | Not confirmed | Not ready for recommendation. | Controller support only | Auto is supported by the controller, but the factory address, baud rate, and serial format still need a manufacturer source. |
| Janitza standard | 101112101 |
Not confirmed from manufacturer defaults. | RS485 Modbus RTU | Not confirmed from manufacturer defaults. | Not confirmed | Not ready for recommendation. | Controller support only | The standard Janitza setup is supported by the controller, but the factory address, baud rate, and serial format still need a manufacturer source. |
Public revision 21/08/2026